Customized supportGet relevant information to your specific car.

Navigation*: setting a destination

This article explains how to set a destination in the navigation system.

Each time a destination is set, it can be saved as a Stored location or Home. The navigation system provides guidance to the destination and up to four intermediate destinations can be added to an itinerary. In many cases, the system can also provide additional Information about destinations.

If the vehicle is connected to the Internet, map destinations can be sent to the navigation system from a web browser using the "Send to Car" app or by using the Volvo On Call mobile app. See also the vehicle's owner's information and the support site at support.volvocars.com.

To set a destination, in the navigation system's normal view, press the thumb wheel/OK/MENU and select Set destination.

P3-1346-NAV-Melco Meny Adress-Hem

Setting a destination using Home

A home location must have been stored before it can be used.
  1. In the navigation system's normal view, press the thumb wheel/OK/MENU and select Set destination→Home.
    Guidance will begin.

Setting a destination using an address

It is enough to enter the name of a city, area, town, etc. in order to be guided to its center.

Note

The definition of a city or area may vary from state to state, and also within the same state. It will sometimes be an entire city, or a particular section of a city.
  1. In the navigation system's normal view, press the thumb wheel/OK/MENU and select Set destination→Address.

  2. Fill in one or more of the following:

    • Country:
    • City:
    • Street:
    • Number:
    • Intersection

  3. For additional information about the destination, select Information followed by the type of information desired:

    • Map: displays a map of the location with additional information when available.
    • Call number[1]: A call will be initiated if a phone number has been provided.
    • Online info.[1]: Additional information can be downloaded from the Internet[2].
  4. To store an address in the system's memory, select Save followed by Stored location or Home.

  5. Set the address as an intermediate destination or a single destination:

    • Add as waypoint: adds the address as an intermediate destination (waypoint) to the itinerary.
    • Set single destination: deletes any previous destinations in an itinerary and starts guidance to the selected destination.

Setting a destination using a point of interest (POI)

A point of interest is a general name for tourist attractions or facilities such as hotels, gas stations, etc.

The map database contains a large number of searchable POIs that can be selected as destinations[3].

  1. In the navigation system's normal view, press the thumb wheel/OK/MENU and select Set destination→Point of interest (POI).

  2. Search for a POI in the following ways:

    • By name: displays the text wheel to search for the name of a POI, e.g., "Peppe's". The entire map area will be included in the search. See also Map and system information.
    • By category: limits the POI search to specific categories (e.g., bank/hotel/museum).
    • Near the car: searches for POIs near the vehicle's current location.
    • Along the route: searches for POIs along the current itinerary.
    • Near the destination: searches for POIs near the destination.
    • Around point on map: searches for POIs by scrolling with the cursor.

    For additional information about the destination, select Information followed by the type of information desired.

  3. To store the address in the system's memory, select Save followed by Stored location or Home.

  4. Set the address as an intermediate destination or a single destination:

    • Add as waypoint: adds the address as an intermediate destination (waypoint) to the itinerary.
    • Set single destination: deletes any previous destinations in an itinerary and starts guidance to the selected destination.

Setting a destination using a stored location

This function is a collection of destinations that have been stored using the menu alternative Save→Stored location.

Please note that one or more destinations has to have been previously stored.
  1. In the navigation system's normal view, press the thumb wheel/OK/MENU and select Set destination→Stored location.

  2. Open the stored destination:

    • Routes: e.g., recorded sections of the route.
    • Other: e.g., stored locations.

    For additional information about the destination, select Information followed by the type of information desired.

    It is also possible to delete or edit a stored destination by selecting Edit, Delete or Delete all.

  3. Set the address as an intermediate destination or a single destination:

    • Add as waypoint: adds the address as an intermediate destination (waypoint) to the itinerary.
    • Set single destination: deletes any previous destinations in an itinerary and starts guidance to the selected destination.

Setting a destination using a previous destination

  1. In the navigation system's normal view, press the thumb wheel/OK/MENU and select Set destination→Previous destination.

  2. Select a destination from the list.

    For additional information about the destination, select Information followed by the type of information desired.

    A destination can also be deleted by selecting Delete or Delete all.

  3. Set the address as an intermediate destination or a single destination:

    • Add as waypoint: adds the address as an intermediate destination (waypoint) to the itinerary.
    • Set single destination: deletes any previous destinations in an itinerary and starts guidance to the selected destination.

Setting a destination using an Internet search

An Internet connection is required, see the owner's information.
  1. In the navigation system's normal view, press the thumb wheel/OK/MENU and select Set destination→Internet search.
  2. Follow the instructions on the screen.

Setting a destination using a zip code

  1. In the navigation system's normal view, press the thumb wheel/OK/MENU and select Set destination→Zip code.

  2. Enter the zip code and the country if necessary.

    For additional information about the destination, select Information followed by the type of information desired.

  3. To store an address in the system's memory, select Save followed by Stored location or Home.

  4. Set the address as an intermediate destination or a single destination:

    • Add as waypoint: adds the address as an intermediate destination (waypoint) to the itinerary.
    • Set single destination: deletes any previous destinations in an itinerary and starts guidance to the selected destination.

Setting a destination using latitude and longitude

P3-1346-NAV-Melco Meny Adress-LatLon-2
  1. In the navigation system's normal view, press the thumb wheel/OK/MENU and select Set destination→Latitude and longitude.

  2. Begin by deciding which type of GPS coordinates are to be used by selecting Format:

    • DD°MM'SS'': location in degrees, minutes and seconds.
    • Decimal: location expressed in decimals.

  3. Enter the GPS coordinates.

    For additional information about the destination, select Information followed by the type of information desired.

  4. To store an address in the system's memory, select Save followed by Stored location or Home.

  5. Set the address as an intermediate destination or a single destination:

    • Add as waypoint: adds the address as an intermediate destination (waypoint) to the itinerary.
    • Set single destination: deletes any previous destinations in an itinerary and starts guidance to the selected destination.

Setting a destination using a position on the map

P3-1346-NAV-Melco Meny Sökning via punkt på karta-2
The cursor's position given in GPS coordinates. To display the name, select Settings→Map options→Position information.
  1. In the navigation system's normal view, press the thumb wheel/OK/MENU and select Set destination→Select point on map.
  2. Move the cursor to the desired position, see also Menus.
  3. To store the position in the system's memory, press the thumb wheel/OK/MENU and select Save followed by Stored location or Home.
    the destination will be stored as a symbol/icon on the map if the function Stored location on map is selected, see also Map alternatives.

  4. Set the address as an intermediate destination or a single destination:

    • Add as waypoint: adds the address as an intermediate destination (waypoint) to the itinerary.
    • Set single destination: deletes any previous destinations in an itinerary and starts guidance to the selected destination.

Setting a destination using the travel guide

Searching using travel guide (not available in all areas) offers suggested destinations/routes according to various themes such as restaurants, scenic drives, sight-seeing, etc.

A travel guide is stored on a USB flash drive that has to be plugged into the vehicle's USB socket in the tunnel console storage compartment.

  1. In the navigation system's normal view, press the thumb wheel/OK/MENU and select Set destination→Travel guide.

    If this menu alternative is not displayed, this is because there are no suggestions for your current location or no USB flash drive is connected.

  2. Select the travel guide using one of the following categories:

    • Restaurants
    • Tourist attractions
    • Hotels
    • Tourist routes
    • Other

  3. If available in the travel guide, to display details, images, or play audio:

    • Details
    • Photos
    • Play audio
  4. Select Start guidance.

Did this help?